Conserto TV samsung de 50" a 85"
UN50TU7000G
Backlight apagado Mau contato no conector da placa da fonte, Foi feito ligação direto do conector da fonte com fio no conector das barras de leds, tudo certo
UN50TU8000G
Não acende Barramento de led Fotoacoplador do setor de controle de led, trocar sem testar
SAMSUNG
UN50TU8000G
Ao ligar, não aparece imagem, ficando em loop constante, sem conseguir ligar a TV. Conforme orientação recebida aqui neste site, por outro técnico, isolei o pino que liga o resistor R44 ao flat cable maior, na VCON da esquerda. Refere-se ao sinal VGH, isolado com uma fita fina no flat. Imagem voltou perfeita.
SAMSUNG
UN50TU8000
Liga leds sem imagem fica reiniciando Defeito no display Isolar trilha VGH ao lado do R44 na régua do display volta funcionar 100%!
SAMSUNG
UN50TU8000
Liga sem imagem e desliga Tela ruim solta o cabo Flex que sai da placa principal se firmar é defeito de tela,pode tentar colocar um durex no cabo marrom,mas nem sempre fica 100x100
SAMSUNG
UN50TU8000G
Mais um caso: Desligando e ligando, loop No flat pequeno (vcom para vcom) lado esquerdo (onde entra o cabo flat da placa principal) da esquerda para direita (como se escreve) isolado 3 trilhas somente, tv funcionando normalmente
SAMSUNG
UN50TU8000G
LIGA DESLIGA SEM PARAR TELA EM CURTO CONTA 11 TRILHAS E ISOLA 7 TRILHAS NO FLAT PEQUENO LADO ESQUERDO EM ALGUMAS FUNCIONA PERFEITA NAO É PARA TODAS.
SAMSUNG
UN50TU8000G
Queimando os LEDs Backligh com tensão acima do normal. Solução: remover R901 de 2.4 ohms. E ficar sossegado que ela não volta queimar os leds.
UN50TU8000G
LIGA, ACENDE BARRAMENTO DE LEDS E SE DESLIGA, SEM IMAGEM, FICA NESSE LOOPING VI VÁRIOS VÍDEOS TENTANDO ISOLAR A CAUSA COM A FAMOSA FITINHA NO FLAT, AQUELE PROCEDIMENTO DE IR PROCURANDO ATÉ ENCONTRAR UM PONTO QUE LIBERE O CURTO DO DISPLAY E A TV LIBERE A IMAGEM. NÃO CONSEGUI DESSA FORMA, POIS O CURTO ESTAVA NO 1º FLAT ESQUERDO, OU SEJA, OLHANDO A TV DEITADA NA BANCADA COM A TELA PRA BAIXO, O FLAT QUE ESTAVA IMPEDINDO A TV DE FUNCIONAR ERA O PRIMEIRO DO LADO ESQUERDO. NA PLACA VCON LADO ESQUERDO TEM O POINT TEST "VGH", FOI CORTAR A TRILHA DESSE VGH QUE VAI PARA ESSE FLAT E A TV FUNCIONOU PERFEITAMENTE SEM RISCOS NA IMAGEM, PARA FACILITAR O CORTE FOI FEITO PERTO DO R44 DA PLACA VCON LADO ESQUERDO, OBSERVE AÍ QUE TEM O POINT TEST DO VGH E O CORTE UE FIZ LOGO EM SEGUIDA, OU SEJA, RETIRAREI ESSA REFERENCIA VGH QUE VAI PARA O PRIMEIRO FLAT ESQUERDO...
UHD UWL02 After a software update on the television, a USB error message is displayed. To complete a software update, the TV must reboot twice in order to apply the update. If the USB is removed prematurely or an unexpected error occurs during updating, the update may fail and the below error will be displayed.
Download the latest software version from Samsung.com and install it manually via USB. Please do not remove the USB or disconnect power until the TV reboots the second time.
SAMSUNG
UHD UWL02 Image Distortion Update T-Con data. Do not replace any parts 1. Download software version 1082.1 or higher from Samsung.com
2. Unzip the file and save the folder T-KTSU2AKUC to the root of a USB drive and bring the USB with you at the time of repair
3. Insert the USB into the USB port on TV
4. Go to Settings → Support → Software Update → Update Now to start the update. Please wait for the update to finish
5. The TV will power off and back on when the update is done
6. After the update is done, the TV needs to be cold booted again manually for T-Con to be updated.
a. Unplug the AC cord for about 30 seconds or
b. Press and hold the power button on the remote until the TV powers off and then back on
UN50TU8000G
Liga e desliga brevemente, pisca backlight e desliga, ficando neste ciclo Defeito de tela, se desligar o flat da v-com menor verá que a tv para ligada, se isolar umas trilhas com fita (em qualquer lado desta v-com) a tv fica ligada, mas sempre tela lisa.)
SAMSUNG
UN50TU8000G
Liga asende a tela sen imagen e desliga pisca stdba duas veses Tela encurto lado menor da regua draiver ta tela solusao ensolar de 4 a

0 Comentários:
Postar um comentário
Assinar Postar comentários [Atom]
<< Página inicial